Please leave a message for us and we will reply in the first time

KRY -40℃~+100℃
Heating Power:5.5kW~60kW
Support OEM customization!


  • Product Function Introduction:

    For power battery charging management, precision temperature control devices for permanent magnet synchronous motors, switched reluctance motors, asynchronous motors and their controllers can be controlled locally and remotely through the LCD control panel;

    It has the function of automatic fault protection and can output corresponding signals to ensure the safety of the equipment. The main components are all international brands, quality assurance, surface high-voltage electrostatic spray treatment, auxiliary equipment can be added according to specific needs.


    Equipment Instructions:

    The temperature range is usually -40°C to 100°C. (Expandable to 150℃)

    Equipped with a powerful circulating pump, while ensuring the delivery of high-viscosity liquids.

    Use frequency conversion adjustment or proportional control valve to control the flow output to achieve high-precision control of the total range of 5% to 100% adjustment.

    The inside of the part is cooled and heated by the glycol aqueous solution.

    The test component needs to go through a specific temperature curve and record the temperature change.



    Temperature control systems are mainly used in two ways: they simulate external environmental conditions in the climate chamber or replace internal systems, such as the cooling circuit of an engine.

    Temperature simulation can ensure that the material remains (dimensionally) stable under extreme temperatures or rapid temperature changes, and the gasket remains leak-free over a wide dynamic range of pressure and temperature, and the pumping system can operate reliably regardless of temperature and viscosity.



    Temp Range-40℃~+100℃
    Temperature control precision±0.5℃
    Temperature feedbackPt100
    Temperature display0.01k
    Flow rate output5~50L/min
    Flow description/When the temp. is below -30℃,When the temp. is below-30℃,

    the maximum flow rate is 25L/min.the maximum flow rate is 30L/min.
    Flow rate accuracy±0.2 L/min
    Pressure displayAdopt the Jeffron pressure sensor, the touch screen display the pressure, can carry on the pressure control adjustment.
    Heating power5.5kW~Optional 60kW




    CompressionEmerson Valley Wheel Compressor
    Expansion valve/solenoid valveEmerson / Danfoss thermal expansion valve
    Oil distributorEmerson
    Dry filter, Pressure controlEmerson / Danvers
    EvaporatorDanfoss/KAORI plate heat exchanger
    Input,DisplaySiemens 7-inch color touch screen Siemens s7-1200 PLC controller
    Program edit10 procedures may be prepared, each of which may be composed of 40 steps
    CommunicationCAN communication bus
    Safety protectionSelf-diagnosis function; freezer overload protection; high pressure pressure switch, overload relay, thermal protection device, low liquid level protection, high temperature protection, sensor fault protection, etc.
    Closed circulationThe whole system is a fully enclosed system. There is no oil mist at high temperature, and low temperature does not absorb moisture in the air. The system does not increase the pressure due to high temperature during operation, and the heat medium is automatically replenished at low temperature.
    refrigerantR404A/ R507C
    Connection sizeG3/4
    Cooling water@25C1500L/H~15000L/H
    Condenser(W)Tube type heat exchanger (Paris/Shenshi)
    Condenser(A)Copper tube aluminum finned heat exchanger (upward wind)
    Power 380V50HZ12kW max~84kW max
    Weight (water cooling)250kg280kg320kg360kg620kg890kg1300kg
    Optional220V 60HZ Three phase  400V 50HZ Three phase  440V 60HZ Three phase
    OptionalExtend to -40~+135℃
    OptionalHigher precision control of temperature, flow and pressure
    OptionalAutomatic antifreeze filling system
    OptionalAutomatic antifreeze filling system

    工厂实力 (1).jpg



    If you need this device, you can communicate with online customer service or leave a message in the form below.