Please leave a message for us and we will reply in the first time

KRY -20℃~+100℃ 1&6
Heating Power:15kW~38kW
Support OEM customization!


  • 4.jpg

    Equipment Instructions:

    The temperature range is usually -40°C to 100°C. (Expandable to 150℃)

    Equipped with a powerful circulating pump, while ensuring the delivery of high-viscosity liquids.

    Use frequency conversion adjustment or proportional control valve to control the flow output to achieve high-precision control of the total range of 5% to 100% adjustment.

    The inside of the part is cooled and heated by the glycol aqueous solution.

    The test component needs to go through a specific temperature curve and record the temperature change.



    Temperature control systems are mainly used in two ways: they simulate external environmental conditions in the climate chamber or replace internal systems, such as the cooling circuit of an engine.

    Temperature simulation can ensure that the material remains (dimensionally) stable under extreme temperatures or rapid temperature changes, and the gasket remains leak-free over a wide dynamic range of pressure and temperature, and the pumping system can operate reliably regardless of temperature and viscosity.

    Temp Range-20℃~+100℃
    Temperature control precision±0.5℃
    Temperature feedbackPt100
    Temperature display0.01k
    Flow control/Group1~20 L/min1~20 L/min1~40 L/min
    Flow control accuracy/Group±0.2L
    Number of fluid output groups6 groups
    Pressure control/group0.2bar~2.5bar
    Flow descriptionWhen the temperature control is lower than -30℃, the flow rate is controlled within 80% of the maximum value.
    Flow pressure descriptionThe unit can control the flow individually or separately. Need to control different solutions at the same time (customized)
    Heating Power15kW25kW38kW


    CompressionEmerson Valley Wheel Compressor
    Expansion valve/solenoid valveDanfoss Thermal Expansion Valve / Emerson Solenoid Valve
    Oil distributorEmerson
    Dry filter, Pressure controlDanfoss
    EvaporatorDanfoss/KAORI plate heat exchanger
    Circulating pumpGerman brand magnetic drive pump
    Frequency converterDelta
    Flow,Pressure sensorElectromagnetic flowmeter, Johnson Controls pressure sensor
    Input, Display10 inch color touch screen Siemens S7-1200 PLC controller
    CommunicationModbus RTU protocol RS485 interface, optional CAN communication bus, Ethernet interface TCP/IP protocol
    Safety protectionWith self-diagnosis function; Refrigerator overload protection; High pressure switch, overload relay, thermal protection

    device, low liquid level protection, high temperature protection, sensor fault protection and other safety functions
    Closed circulationThe whole system is a fully closed system, there will be no oil mist at high temperature, low temperature does not
    systemabsorb water in the air, the system in operation will not because of high temperature pressure rise, low temperature

    automatically add heat conduction medium.
    Connection sizeThere are six groups of inlet and outlet,G3/4
    Cooling water@20C8000L/H12000L/H20000L/H
    Condenser(W)Shenshi tube type heat exchanger
    Condenser(A)Optional air-cooled type, upper air outlet, the equipment size will be increased.
    Power 380V50HZ36kW max51kW max75kW max
    Dimension cm120*180*205145*205*225145*205*225
    Optional220V 60HZ Three phase  400V 50HZ Three phase  440V 60HZ Three phase
    OptionalExtend to -40~+135℃
    OptionalThe size external circulation pipe line is DN15 or DN20, do not throttle, which will increase the circulation pump load,

    pipe need to be insulated, and adopt rubber and plastic insulation pipe which can afford high temp.

    工厂实力 (1).jpg



    If you need this device, you can communicate with online customer service or leave a message in the form below.